pasobchain.blogg.se

1. #JDSU HST 3000 ETHERNET TESTING HOW TO#
2. #JDSU HST 3000 ETHERNET TESTING PORTABLE#
3. #JDSU HST 3000 ETHERNET TESTING SOFTWARE#

This document provides procedures for Metro Ethernet service up to 1 Gbps, including:

#JDSU HST 3000 ETHERNET TESTING PORTABLE#

Scope This document covers Ethernet testing procedures used for Business Services customer activation, fault isolation, and troubleshooting using the JDSU HST-3000 portable business services tester. Through Settings menus and configure/update your test as follows.Technical Support 85 Field Applications Engineer 32 Using the Right Arrow key or Settings soft key, scroll Have previously saved configuration files, press the Save soft key, then Press the Configure Navigation key to configure test setting. Select 1G Terminate, and press the OK key. For Layer 3 IPv4 Optical Testing, press the ETH OPTIC Soft key,.For Layer 3 IPv4 Electrical (Copper/RJ-45) Testing, press the ETH.For Layer 2 Optical Testing, press the ETH OPTIC Soft key, selectġG Terminate, and press the OK key.For Layer 2 Electrical (Copper/RJ-45) Testing, press the ETHĮLEC Soft key, select Terminate, and press the OK key.Use CAT 5E or better cable for copper 10/100/1000BASE-T Use Yellow Single Mode Fiber jumper cables for 1310 nm Use Orange Multimode jumper cables for 850 nm 1000BASE-SX.Into the optical SFP connector labeled R/T 1.īefore connecting to an optical link, make sure all fiber optic cables andĬonnectors are clean using a Fiber Inspection microscope.Ĭonnect the Ethernet test port to the Ethernet switch port under test.

#JDSU HST 3000 ETHERNET TESTING SOFTWARE#

WaitĪpproximately 1 minute for the Base Unit software to load.įor optical testing, insert desired SFP (1000BASE-SX, 1000BASE-LX) Press the green Power Key to turn on the HST-3000. Use this procedure to set up an HST-3000 to test a 10Mbps, 100Mbps, or 1000Mbps link.

The RFC-2544 test is run from the A-Side. His location (A-side or Z-side) and whether he is using a T-BERD 5800, T-BERD 6000A, SmartClassĮthernet, or HST-3000 test equipment. Technicians should follow procedure in one of the following sections, depending on Procedures are described for RFC-2544 Tests to verify throughput, round trip delay, jitter, and frame

#JDSU HST 3000 ETHERNET TESTING HOW TO#

The following procedures describe how to measure throughput, frame loss, round trip delay, and jitter Scroll to the desired selection and pressing the OK key. HST-3000 front panel by using the keypad to select the option number or by using the arrow keys to Inspection kit to help turn-up and maintain Ethernet links.

The HST-3000 works in conjunction with a fiber cleaning and AnĮthernet SIM is required for this test. Interface modules (SIMs) to support Ethernet, T1/T3, Copper/DSL and other access technologies. The product supports a variety of subscriber The HST-3000 is a portable test tools for Ethernet testing. Performance of an Ethernet circuit and to verify conformance to the agreed upon Service Level At customer activation, this test equipment is used to validate the Updated process for HST-3000 Firmware Revision 7.41.03.Īdded check for Autonegotiation mismatch.Īdded instructions for SmartClass Ethernet loopback device.Īdded instructions to save and load configuration.įault isolation and troubleshooting. Whenever a fiber is disconnected and reconnected. Allįibers and connectors must be cleaned and inspected when service is turned up on these fibers and This document mandates proper care, cleaning, inspection, and handling of fiber optic connectors. RFC-2544 is a recommended test suite for verifying key performance indicators for Metro Ethernet Layer 2 and Layer 3 IPv4 RFC-2544 tests between the HST-3000 and SmartClass Ethernet Layer 2 and Layer 3 IPv4 RFC-2544 tests between the HST-3000 and T-BERD 6000A Layer 2 and Layer 3 IPv4 RFC-2544 tests between the HST-3000 and T-BERD 5800 Layer 2 and Layer 3 IPv4 RFC-2544 tests between two HST-3000s Thisĭocument provides procedures for Metro Ethernet service up to 1 Gbps, including: This document covers Ethernet testing procedures used for Business Services customer activation,įault isolation, and troubleshooting using the JDSU HST-3000 portable business services tester. JDSU HST-3000 RFC-2544 Ethernet Testing Guide